First, emancipate the mind, enterprises should adjust, transform, upgrade and innovate.
Everyone eats instant noodles when they are busy on business trips. If no technicians produce instant noodles, there would be no instant noodles market nowadays, only flour market. Therefore, on the way of enterprise development, the enterprise leadership must first emancipate the mind, change ideas, be brave to innovate, can not rely solely on the improvement of production but on the improvement of product quality.
Our diamond application market, diamond fine materials, diamond powder, diamond fine powder, nanometer powder, etc., the market is very large, for example, now the ordinary computer saturated, go to the production of tablet computers. With the development of science and technology and economy to a certain extent, you must constantly open up the market and occupy the market. Depending on traditional industries and traditional products, it is almost impossible to rely on innovation. Innovation is not unattainable, innovation is everywhere, in short, there are technological innovation, technological innovation, product innovation, management innovation. Catalyst materials and sheet catalysts for synthesizing diamond in our industry have remained in production for more than 20 years, and have since been replaced by powdered catalysts. The production enterprises failed to make timely transformation and upgrading, and finally the business went bankrupt.
Two. Vigorously develop superhard tools and drilling tools.
The higher precision green environmental protection products, the greater the support for other high-tech industries, to solve the traditional tools difficult to process, especially the processing of hard and brittle materials, improve production efficiency and precision, reduce environmental pollution. According to statistics, last year spent 48 billion 500 million yuan, and the engineering drilling tool was about 20000000000 Yuan. China's aerospace, automotive, military, high-speed rail, subway, mines, tunnels, oilfields, the development of tools, drilling tools, such as geological mine rock complexity and oil exploitation, drilling depth from hundreds of meters to thousands of meters of deep wells, with cemented carbide tools, drilling tools is not competent, must use superhard materials Material cutting tools and drilling tools. Composite cutting tools (PDC, PCD) have developed at a rate of 45% in the past two years. However, as a cutting tool, it has a great gap with the international community, accounting for only 1% of the total cutting tools, while Japan, the United States accounted for 4-5% of the total cutting tools, Russia accounted for 4-7%. The service life and processing efficiency of the composite cutting tool have been increased by several dozen times and hundreds of times. The dust in the production process has been avoided. The cutting fluid has polluted the environment and realized clean production.
Three. Development of new functional composite materials
With the progress of the times, the development of science and technology, especially the development of national defense and military technology, but metal materials also have limitations in the use of the process, such as aerospace, defense air products are said to be all disciplines of joint operations, most of them are made of composite materials. The conformity between ordinary steel and superhard material greatly improves the performance of conforming material, and its hardness, strength and toughness are better. It can be used in shield machine of Metro big drill bit. Yale University has developed C~si composites, light and hard and environmentally friendly. Graphene products developed by Korea Academy of materials science. Our country also attaches great importance to it, including it in the 973 plan, and in September last year in Ningbo, Zhejiang, held the International Graphene Innovation Conference, the preparation for the establishment of the International Graphene Union. Graphene can replace silicon, and its speed is one hundred times faster than that of silicon. Some people have done experiments, adding graphene to phenolic resin curing, impact strength increased by 150%, bending degree increased by more than 40%. Adding graphene to a variety of network conforming to the material "light core net" its strength, impact strength, wear resistance are significantly improved. Some people have analyzed that graphene can promote global scientific and technological progress.
Four, vigorously develop new markets.
Beginning in 2015, the industry is still shuffling, many small enterprises will be eliminated, low-tech large enterprises will be eliminated, we have many small diamond processing plants closed, there are cemented carbide tools plants, drilling tools plants are also facing bankruptcy, to survive we must improve product quality, stable production quality, enterprises. The family must have a sense of crisis, continuous innovation, and constantly develop new products, so that enterprises can remain invincible.
